在施工过程中，严格执行《建筑工程施工验收规范》及国内的有关法规规定，保证施工质量达到优良标准。一、硬化耐磨地坪施工、验收执行的行业标准:1.参照我国现行的整体地面面层钢屑水泥所规定的施工规范及验收标准评定； 2.耐磨地坪行业的现行标准：

In the course of construction, the Code for Acceptance and Acceptance of Construction Projects and the relevant domestic laws and regulations are strictly implemented to ensure that the construction quality meets the excellent standards. 1. Industry standards for construction and acceptance of hardened and abrasion-resistant floors: 1. Assessment according to the construction specifications and acceptance standards stipulated by the existing steel scrap cement for the overall floors in China; 2. Current standards for the industry of abrasion-resistant floors: 检验项目、检验要求、检验方法、检验数量、

Inspection items, inspection requirements, inspection methods, inspection quantities, etc.

平整度 、小于4㎜ 、平尺、塞尺、 代表性的自然间抽查10% 、

Flatness, less than 4, flat ruler, feeler gauge, representative natural sampling 10%.

裂缝 、不允许、 目测、 全数、

Cracks, not allowed, visual, total,

抗压强度、 非金属骨料、 不小于70Mpa 、一个工程一组、

Compressive strength, non-metallic aggregate, not less than 70Mpa, one engineering group.

金属骨料 、不小于80Mpa、

Metal aggregate, not less than 80Mpa,

耐磨性 、非金属骨料、 不大于290MG/250转、 一个工程一组、

Wear resistance, non-metallic aggregate, no more than 290MG/250 turn, an engineering group.

金属骨料 、不大于200MG/250转

Metal aggregate, not larger than 200MG/250

二、质量保证措施：

Two, quality assurance measures:

1.建立健全以项目经理为主的质量保证体系和质量管理网络，做到纵向到底，横向到边，认真贯彻各项技术管理制度，落实责任到人。

1. Establish and improve the project manager-based quality assurance system and quality management network, vertical to the end, horizontal to the side, conscientiously implement the technical management system, the implementation of responsibility to people.

2.加强技术管理，认真贯彻国家规定、操作规程及各项管理制度；明确岗位责任制，做好技术交底工作，并建立技术考核制度。

2. Strengthen the technical management, conscientiously implement the state regulations, operating procedures and various management systems; clarify the post responsibility system, do a good job of technical disclosure, and establish a technical assessment system.

3.推行全面质量管理，坚持质量三检制（即自控、互控、交接控）、样板制和岗位责任制，实行主要操作者姓名、级别、质量等级挂牌上墙制。

3. Implement total quality management, adhere to the quality of the three inspection system (i.e. automatic control, mutual control, hand-over control), model system and post responsibility system, the implementation of the name of the main operators, grade, quality grade listing on the wall system.

4.加强原材料的检查工作，严格执行各种原材料的检测制度，一是检验出厂合格证，严格控制各种配合比的计量。

4. Strengthen the inspection of raw materials, and strictly implement the inspection system of various raw materials. First, inspect the factory certificate, strictly control the measurement of various mix ratios.

5.加强与土建单位的配合，互相协调、互相监督，监督砼的强度，监督砼的平整度及标高。

5. Strengthen cooperation with civil construction units, coordinate and supervise each other, supervise the strength of concrete, supervise the flatness and elevation of concrete.

6.加强技术资料的管理工作，严格按照工作质量检测评定标准，及时整理归档，做到资料与工程同步进行，真实反映工程的实际情况。

6. Strengthen the management of technical data, strictly in accordance with the work quality testing and evaluation standards, timely collation and filing, so that the data and the project go on simultaneously, truly reflect the actual situation of the project.